Open Audio levels
- Open your video in the editor.
- Click Audio in the left toolbar.
- Click Audio settings (the sliders icon) in the panel header.
Read the level meter
While your video plays, each volume slider shows a live level meter in its track, so you can see how loud that sound is in the final mix. Master volume meters everything together, and the microphone, system audio, B-roll media, background music and sound effect sliders each meter their own sound.- A light tint fills the track up to the current level.
- A tick marks the loudest point of the last second. It turns orange near the top and red when the sound is close to clipping.
- The percentage turns red for two seconds when the sound clips. Lower that slider until it stops.
Adjust the master volume (applies to the whole video)
Master volume is the default control. It sets the overall level of:- your microphone audio
- your system audio (sound recorded from your screen)
Use advanced audio settings (control each source)
Open Advanced audio settings to adjust each audio source separately.- System audio volume: lower it or switch it off, for example if you recorded sound playing on your screen by accident.
- Microphone volume: boost it if your mic is too quiet (for example, you sat too far away), or turn it down if it’s too loud.
- Media volume (this layout): if the current layout uses a video as B-roll media, set that video’s volume for the current layout. When both the Screen and Camera slots contain media, the label names the slot, such as Screen media volume (this layout). Lower it to mute background sound or raise it when the media’s own audio should come through.
Open a B-roll video’s volume controls
Jump straight to a B-roll video’s volume slider from the layout timeline:- Right-click a layout section that contains video media.
- Select Adjust volume. If both the Screen and Camera slots contain media, select Adjust screen volume or Adjust camera volume.
- Tella opens the Audio panel. Click Audio settings to reach the volume slider for that media under Advanced audio settings.
When a B-roll section uses a camera-only layout, Tella hides the source video but keeps your camera audio playing, so your voiceover continues while the B-roll fills the screen.
Mute an entire clip
To mute every audio source in a clip without opening the Audio panel:- Right-click the clip on the timeline, or click the clip to select it and click ⋯ on its name label.
- Select Mute audio.
Mute the whole video’s own sound
Turn on Mute video under Audio levels to silence every clip’s own sound at once. Background music and sound effects keep playing. Turn it off to bring the clips’ sound back.Lower or mute part of a clip
To turn down a cough, a breath or a noisy stretch without touching the rest of the clip:- Drag across the clips on the timeline to select the part you want to change.
- Right-click the selection and choose Volume, or with Audio open, click More actions (⋯) in the toolbar above the timeline and choose Volume.
- Pick Mute, 75%, 50%, 25% or 10%.
- Click the card to set an exact level with its Volume slider (0 to 100%), or click Delete volume change to restore the original volume.
- Right-click the card to pick another level or choose Restore volume.
- Drag either end of the card to change how much of the clip it covers.
Adjust audio for a single clip
By default, audio adjustments apply to all clips in your video. To give one clip its own microphone and system audio levels (B-roll media volume is always set per layout):- Click the clip on the timeline so the playhead is in it.
- In the Audio panel, click Audio settings, then tick Adjust this clip only under Master volume.
- Under Advanced audio settings, set Mic volume (this clip) and System audio (this clip).
Reset a clip back to the main volume
To drop a clip’s custom levels, click the clip on the timeline, open Audio settings, and untick Adjust this clip only. The clip goes back to the video-wide levels.Background music volume
Once your video has music, Music volume appears under Audio levels. It sets the volume of every song together, so you can balance the music against your voice and system audio. To change one song only, click its card on the timeline and drag its Volume slider. See Add background music for how to choose or upload a track. Tip: if your voice is hard to hear, try turning the music down and boosting the microphone slightly.Related
- Add background music
- Studio Voice (audio enhancement)
- Add sound effects: each sound effect has its own volume control