Remove silences automatically in the editor’s Cut panel: under Silences, choose Natural, Fast, or Faster, then click Remove N silences (for example, Remove 12 silences). Tella only treats a pause as silence when every unmuted audio track is quiet, and you can undo it with Reset silences or Reset all cuts.
-
Open your video in the Tella editor.
-
Click Cut in the left toolbar (or press
C) to open the Cut panel.
-
In the Cut panel, locate the Silences tool.
What’s the difference between Natural, Fast, and Faster?
The modes set how aggressively silences are removed:
-
Natural: Removes larger silences, keeping a conversational flow.
-
Fast: Removes smaller silences, for a more concise video.
-
Faster: Removes very short silences, for the most condensed video.
See how much time a mode saves
In the Silences section, choose Natural, Fast, or Faster. Tella analyzes every clip in your video for that mode and shows the number of silences detected across the video and the total time removing them will save.
How silence detection works with multiple audio sources
If your recording has more than one audio source (for example, your microphone and your screen recording’s audio), Tella marks a region as silence only when every audible audio source is quiet at the same time. So if you’re silent but your screen share is playing audio (a demo, a video, or music), that section isn’t flagged as silence. This is automatic.
Tella treats inaudible digital noise as silence, so a screen audio track that sounds silent won’t stop pauses in your microphone audio from being detected.
Speech-aware detection on voice tracks
For voice audio tracks (like your microphone), Tella combines waveform loudness with speech detection and your transcript to decide what counts as silence:
-
Noisy microphones: Constant low-level background noise (fans, HVAC, or mic hiss) does not prevent pauses outside detected speech from being marked as silence.
-
Pauses between words: Dead air close to your room’s background noise level counts as silence even right next to your words, so each cut reaches the end of the word instead of leaving a short gap. The fading end of a word is kept.
-
Quiet speech: Speech detection and your transcript protect low-volume speech, like soft consonants or the other side of a call picked up by your mic, from being cut.
Loud non-speech content like music, applause, or sound effects is kept as audio.
Muted layers are excluded
A layer you’ve muted by setting its volume to zero is excluded from silence detection. For example, if you recorded your screen with system audio you don’t plan to keep, mute the screen layer and Tella detects silences from your microphone audio alone instead of requiring both tracks to be silent.
The timeline shows waveforms for all audio sources: your microphone audio in the primary color, other sources (like screen recording audio) in a muted gray.
Remove the detected silences
-
After selecting a mode, click Remove N silences (for example, Remove 12 silences).
-
Tella removes the detected silences from every clip in the video. The timeline closes up the gaps; to see where the cuts are, open More actions (⋯) in the playbar above the timeline and choose Show cuts.
After removing silences with Natural or Fast, the mode selector stays available: choose a stricter mode to analyze the remaining pauses and remove more silences without resetting your edits. After Faster, the most aggressive mode, it’s hidden.
Adjust a silence cut by hand
-
Go to the area on the timeline where a silence was removed.
-
Click the piece of the clip next to the cut to select it. Only a selected piece shows edges you can drag.
-
Drag its edge to adjust where the silence removal begins or ends.
-
Play back the video to check the edit.
Undo silence removal
Click Reset silences (the circular arrow next to Silences in the Cut panel), or open More actions (⋯) in the playbar above the timeline, click Reset all cuts, and confirm with Reset all.
Both restore every cut in every clip of the video, not only the silences, so any manual cuts you made are undone too. Press Cmd + Z (Mac) or Ctrl + Z (Windows) to bring them back. You can then select a different mode or manually edit the silences. Last modified on November 19, 2026